Flexnet Server License AdministratorPTC License
FlextNet Publisher Version 11.13 is shipped with Creo 4.0. Installing and Configuring the Flexera FLEXnet® License AdministratorPTC License Server. Installing, Configuring, and Administrating a FlexNet License Server for. Lmgrd - the FlexNet server daemon lmutil - the FlexNet licensing utilities lmtools.exe - the graphical user interface for FlexNet licensing utilities. The software contains: armlmd - the ARM vendor daemon. Download FlexNet Publisher Software describes the download process.
Other vendors may also use the FLEXnet service. The preferred solution is to set up both licensing services on the same server if the customer is using Network licensed (multi-user access) Revit, or Ideate Software licenses can be run on a separate server.In addition to the Autodesk Network License Manager, Autodesk products can be configured to use the 3rd party Flexera FLEXnet License Administrator service to manage licenses for the Autodesk network applications. The Autodesk License Manager (FlexLM) works with both Autodesk Revit and Ideate Software to manage floating network licenses.
Flexnet Server Install FlexNet Publisher
On the Introduction, click Next. Once the installation has been uncompressed you will be presented with the installation screen. To obtain the installation files for this application, you need to download the license administrator files ( lmadmin*.exe) from the following website: FLEXnet License Administrator is not supplied by Autodesk. Only one license manager type should be used for all products.To use GeoStudio with network licenses, you must install FlexNet Publisher License Server Manager (hereafter referred to as lmadmin) on a server on your.For new installations of FLEXnet, please use the following procedure:
If there is any important information listed for a prerequisite install, please follow the recommendations listed on this screen and click Next to continue. On the Pre-Installation Summary, review the settings and click Install. Regardless of any pre-existing license manager, do not choose to import any settings. If you receive the following error, either rename the existing folder ( recommended) or choose a new location for installation. Click Next to continue.Note: You cannot upgrade an existing license manager. Default is C:\Program Files\FLEXnet Publisher License Server Manager.
Your browser should now automatically open to the FLEXnet License Administrator Dashboard and display the demo vendor daemon information.The default location for the web-interface can be accessed by the following URL(s): servername:8080 – Access across the network or Internet. Click Done to complete the install process. When prompted to launch the License Server Manager, check the box that reads Start server now and click Next to continue. Note: If you do not configure FLEXnet to run as a service, you will have to manually start the service on each restart/login. On the Service Configuration, be sure to check the box that reads, Run as a service to ensure that the lmadmin service is created and configured properly. The License Server port number will default to 27000 ~ 27009.
Later you can add additional users either created locally or from your Domain Controller.Click Submit and Save the new admin password to continue.On the User Configuration screen, you can add additional administrators as local users or from your Domain Controller. Please choose a secure password that can be easily remembered. You will be required to login as admin on the initial login.Upon a successful login, you will immediately be asked to change your admin password.
You should use your existing license file provided by Autodesk or the Reseller. The FLEXnet License Administrator is now ready to be configured with the Autodesk *.lic file. Choose Vendor Daemon Configuration from the left-side navigation.Locate the vendor daemon listed as demo and choose Delete.When the confirmation dialog box appears, click OK to delete.
Once the license file has been imported, you should receive warning that service is unable to start because the adskflex.exe vendor file required by this license is missing.The warning will provide the location where it expects the adskflex.exe vendor file to be placed.Obtain the adskflex.exe vendor file from the Autodesk Network License Manager (LMTOOLS) installation folder - or attached to this post - and place it in the directory specified by the warning:C:\Program Files\FLEXnet Publisher License Server Manager\adskflexNote: This location is not the same folder as the license file.Click OK to accept the warnings and to continue to the next step. Select the file and then click Import License to continue. While still on the Vendor Daemon Configuration screen, click Browse… to navigate to the location where you saved the license file in the previous step. You can also place any adskflex.opt options files here as well, if applicable.
Alerts can be modified from the Alert Configuration screen under Administration. Once running, click Dashboard on the upper-right corner and choose Concurrent to display your network licenses.You can clear any errors or warnings listed in the alerts from initial setup and configuration. The status may be pending, but will eventually show as running if configured properly and refreshed. The status of the adskflex vendor daemon should now be listed as RUNNING and using port 2080. The status should change to: Successfully updated the vendor daemon configuration.You can now click Start on the vendor daemon to start the FLEXnet License Administrator. The path should now read:Click Save.
Therefore it is only necessary to use the 32-bit version of the adskflex.exe vendor daemon2. It will be installed as a 32-bit web application on 64-bit servers. The FLEXnet is available only in 32-bit versions. Good Luck!The following are known issues with the FLEXnet License Administrator:1. Special thanks to Darin.Green for requesting that I write an installation and configuration guide for this license manager.The necessary adskflex.exe 32-bit version is attached to this post for your convenience. Note: All other options should remain defaults unless you have specific reason to change them due to preference or conflict.Optional: To modify the startup behavior of the service, see the Startup type under Windows Services in Administrative Tools (services.msc)You should now be able to access the FLEXnet License Administrator via the web browser and using the credentials created in Administration.At the time of this post, the latestion version is 11.10.0.2.
When I reserved a seat of ARCHDESK_2010, it doubled the reservations as well. As it turns out, this is only a graphical error as the working of the license manager are still as expected. Please use at your own discretion.For information on the Autodesk Network License Manager (LMTOOLS) please see my original signature post here:Okay, for an update on the conversation between us off record, I have determined that the issue of license doubling is simply a graphical anomoly.I have run the actual LIC file thru the license parser and it came back with the correct amount of seats.When I ran the BDSPRM in the FLEXnet, however, it did show 2x licensing for the same 2010 products as in your screen capture. It is suggested that this be used for testing purposes only. This license manager is not approved for use by Autodesk and will not be supported in production environments.
See image below:Been using 11.12 since around 2014 but could never get a newer copy after the globes site took it off. This tells me that there is a interpretation issue with your PACKAGE Feature Code and not the INCREMENT line. Combining your 5 seat and 1 seat yielded 12 seats for 2010 but only 6 work total. I was unable to reserve more than the maximum amount of seats owned regardless of the number shown on the Dashboard.
Tried on a test server and it worked but since I was going to do this all over I was determined to find the newest copies as Flexera only releases to their subscribed customers and its up to them to distribute support files. I never had a problem even using Autodesk 2016 products.I got laid off for over a year but called back and found that they went back to the old console version due to "incompatible" with 2016.
0 kommentar(er)
